Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
- System of cooling, heating
   Separation and replacement of hoses of system of cooling
   Removal, survey and radiator installation
   Removal, check of serviceability and thermostat installation
   Serviceability check, removal and electrofan installation
   Serviceability check, removal and installation of gauges of system of cooling
   Removal and installation of the water pump
   The general description of a heater
   Removal and installation of components of a heater (all models except Scenic)
   Removal and installation of components of a heater (model Scenic)
   The general description and precautions - air central air
   Removal and installation of components of a central air of air
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of components of a heater (model Scenic)

MODELS WITHOUT AIR CONDITIONER

The control panel a heater/ventilation

 REMOVAL AND INSTALLATION

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment).
2. Remove lighter as the Onboard electric equipment is described in the Head.
3. Turn away the block of management and take it from the instrument panel.
4. Disconnect electroconducting sockets, then separate скобы casings of ropes from the block and separate ropes from their levers. Pay attention that management ropes have colour labels. If it is necessary, disconnect the block of management from the instrument panel.
5. Make installation in return sequence. Be convinced that ropes are attached reliably everyone on a former place. The rope of adjustment of temperature of air has a red label, and a rope of the distributor of air - blue. Check up control panel functioning before installation прикуривателя.

Ropes of management of a heater

 REMOVAL AND INSTALLATION

1. Remove the management block as it is described in paragraphs above. Access to fixing details of ropes on the right party of a casing воздухораспределителя can be received and from under the instrument panel, and through an aperture under the management block. Turn away a bolt and uncover, located under the instrument panel on the right (address to an accompanying illustration).

2. Mark ropes of management and their fixing скобы on a casing воздухораспределителя not to mix ropes at installation.

3. Unhook fixing скобы, then separate ropes from a casing воздухораспределителя and levers and take them from the panel. Pay attention that ropes have colour labels (address to an accompanying illustration).

4. At installation, deduce ropes into position, being guided on colour labels (red at a rope of adjustment of temperature and blue at a rope of the distributor of air).
5. Fasten ropes to casing levers воздухораспределителя and attach casings of ropes. Using the labels made before removal, attach both ropes fixing скобами. Establish the block of management and check up functioning of ropes.

The motor of a supercharger of a heater

 REMOVAL AND INSTALLATION

1. Disconnect a cable of weight from the battery.
2. Displace a site of a sealant of the right door and remove plastic internal furnish of a threshold.
3. Let out a plait of wires of the motor of the supercharger, located under the panel at level of ware boxes, moving from the car middle to a door.
4. Remove поролоновый the loose leaf from under a supercharger, then disconnect an electroconducting socket.
5. Turn away three bolts and take assemblage of the motor of a supercharger.
6. Turn the block on 90 counter-clockwise and remove it.
7. Make installation upside-down.

The block of management of work of the motor of a supercharger of a heater

 REMOVAL AND INSTALLATION

1. The management block is behind the panel on a left-hand side.
2. Disconnect a cable of weight from the battery.
3. Disconnect conducting, then turn away the bottom fixing bolt of the block of management.
4. Loosen the a bolt of the top fastening, incline the block back and remove it.
5. Make installation upside-down.

Casing воздухораспределителя

 REMOVAL AND INSTALLATION

1. Merge a liquid from cooling system. Alternatively, press hoses of the heat exchanger of a heater as it is possible more close to a partition of an impellent compartment.
2. Remove assemblage of the instrument panel as it is described in the Head the Body.

3. Loosen the collars also remove hoses of system of cooling from branch pipes of the heat exchanger of a heater (address to an illustration).

4. Remove consolidation from an upper edge of a partition of an impellent compartment.
5. Turn away screws of fastening and remove the panel дефлектора the ventilating aperture located at a windscreen (on the right).
6. Loosen the also remove a casing bolt воздухораспределителя (address to an accompanying illustration).

7. Working in an impellent compartment, turn away a nut of the top arm on a partition and two bolts at the block basis (address to an accompanying illustration).

8. Turn away the bolts of two tubes bearing a liquid located on a lateral wall of a casing, and separate assemblage of tubes from the heater and casing heat exchanger. Закупорьте the ends of tubes and branch pipes of the heat exchanger of a heater not to pour cooling liquid in salon. Impose a casing with rags as precaution and immediately erase the spilt drops of a cooling liquid a damp fabric to prevent formation of stains.
9. Be convinced that have taken away from a casing of a wire and ropes and have separated from it all attached components.
10. Accurately separate assemblage of the bottom air line and a casing from a partition and take it from the car. Try not to spill thus cooling liquid.
11. Make installation upside-down. At fastening of tubes to the heater heat exchanger use new consolidations. In summary, finish to norm liquid level in cooling system.

The heater heat exchanger

On models with a two-section casing it is enough to remove only the right half of casing.

 REMOVAL AND INSTALLATION

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment).
2. Merge a liquid from cooling system. Alternatively, press hoses of the heat exchanger of a heater as it is possible more close to a partition of an impellent compartment.
3. Loosen the collars also remove hoses of system of cooling from branch pipes of the heat exchanger of a heater.
4. Merge from the heat exchanger as much as possible liquid, forcing air through its top branch pipe. Be ready to an exit of a liquid from the bottom branch pipe and if it is possible, take away a stream from the engine.
5. Turn away a bolt and uncover, located below the instrument panel at the left.
6. Turn away a bolt of fastening of the tubes bearing a liquid, located on a lateral wall of a casing, and three bolts, fastening the heater heat exchanger to a casing воздухораспределителя.
7. Separate tubes from the heat exchanger, trying not to spill cooling liquid in salon. Impose a casing with rags as precaution and immediately erase the spilt drops of a cooling liquid a damp fabric to prevent formation of stains.
8. Take the heat exchanger of a heater from a casing, trying not to damage its plate.
9. Make installation upside-down. Use new consolidations of tubes.

MODELS WITH AIR CONDITIONER

 REMOVAL AND INSTALLATION

1. On the models equipped with the conditioner of air, the motorist can make only removal/installation of the panel and ropes of management of a heater, and also the block of management of work of the motor of a supercharger. These actions are similar described above (address to Section Removal and installation of components of a heater (all models except Scenic)).
2. Removal of the motor of a supercharger, a casing воздухораспределителя, the heater and motor heat exchanger заслонки a mode recycling air should be entrusted HUNDRED Renault as these actions mean separation of tubes bearing a coolant.

Do not separate components of a central air of air while it is not discharged.