Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
- System of cooling, heating
   Separation and replacement of hoses of system of cooling
   Removal, survey and radiator installation
   Removal, check of serviceability and thermostat installation
   Serviceability check, removal and electrofan installation
   Serviceability check, removal and installation of gauges of system of cooling
   Removal and installation of the water pump
   The general description of a heater
   Removal and installation of components of a heater (all models except Scenic)
   Removal and installation of components of a heater (model Scenic)
   The general description and precautions - air central air
   Removal and installation of components of a central air of air
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of the water pump

MODELS WITH THE PETROL ENGINE OF 1.4 AND 1.6 L

 REMOVAL

1. Merge a liquid from cooling system.
2. Remove gear приводной a belt (the Head engine Repair see).
3. Turn away bolts of fastening and remove assemblage of the pump from the engine. Remember an arrangement of adjusting pins of the pump and remove them if they are badly fixed.


 INSTALLATION

1a. Clear and dry contact surfaces of the pump and the block of cylinders.

1b. Then put on a sealing surface of the pump a hermetic layer (Renault recommends use Lostite 518) thickness 0.6 - 1.0 mm (address to an accompanying illustration).

2. Be convinced that adjusting pins are placed everyone on a former place, then deduce the pump into position. Establish bolts of the pump and tighten them reliably.
3. Establish gear приводной a belt (address to the Head engine Repair).
4. Fill cooling system.

MODELS WITH THE PETROL ENGINE OF 2.0 L

 REMOVAL

1. Merge a liquid from cooling system.
2. Поддомкратьте a forward part of the car also establish it on axial props. Remove the right forward wheel and the loose leaf of its arch
3. Loosen the three bolts of fastening of a pulley of the water pump, then remove auxiliary приводной a belt as Maintenance service (address to an accompanying illustration) is described in the Head.
4. Turn away bolts of fastening and remove a pump pulley.
5. Turn away bolts, fastening the pump to the block of cylinders, and take the pump from the block (address to an accompanying illustration). If the pump does not act in film, пристукните on it киянкой. Remove a lining.


 INSTALLATION

1. Begin installation, carefully having cleared combined surfaces of the pump and the block of cylinders.
2. Make installation in return sequence, paying attention to the following:
a) Use a new lining of the pump.
b) Establish and pull auxiliary приводной a belt as Maintenance service is described in the Head.
In summary, fill cooling system (the Head Maintenance service)

DIESEL MODELS

 REMOVAL

1. Remove auxiliary приводной a belt (the Head Maintenance service), preliminary having weakened bolts of fastening of a pulley of the water pump.
2. Merge a liquid from cooling system (address to the Head Maintenance service).

3. Turn away bolts of fastening and remove a pulley drive a belt from the water pump (address to an accompanying illustration).

4a. Turn away fastening bolts.

4b. Then deduce the water pump from working position (address to illustrations). Remember an arrangement of adjusting pins of the pump and remove them if they are badly fixed. Remove a pump lining - it is subject to replacement.


 INSTALLATION

1. Clear and dry up combined surfaces of the pump, a casing and the block of cylinders and place adjusting pins everyone on a former place.
2. Lay a new lining and establish pump assemblage. Tighten fastening bolts.
3. Establish a pulley of the water pump, then приводной a belt and pull it as Maintenance service is described in the Head. Tighten bolts of fastening of a pulley.
4. Fill cooling system (address to the Head Maintenance service).