Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
- Maintenance service
   The routine maintenance schedule
   Checks of levels of liquids
   Check of a condition and pressure in tyres
   Check of brushes of a screen wiper
   Check of a condition and degree of gymnastics of the storage battery
   Check of lamps and safety locks
   Replacement of impellent oil and the filter
   Removal of water from the fuel filter of the diesel engine
   Check колодок forward brake mechanisms and disks
   Check of final system
   Suspension bracket and steering check
   Check of protective covers of a power shaft and SHRUS
   Check of hoses on presence of leaks of a liquid
   Check of an inhaling of bolts of wheels
   Replacement of the dustproof filter
   Check of level of a liquid of automatic transmission
   Check of system of release
   Check of a central air of air
   Check of system of an onboard electric equipment
   Check of a sheeting of the bottom
   Check of pressure of pressurisation (diesel models with турбокомпрессором)
   Check of seat belts
   Check and replacement auxiliary drive a belt
   Replacement of spark plugs and check of system of ignition
   Replacement of a filtering element of the air filter
   Replacement of the fuel filter of the diesel engine
   Check of system of heating and ventilation
   Greasing of hinges and locks
   Check of spare fuses
   Check of a thickness колодок back brake mechanisms
   Check of level of oil of a manual box of a gear change
   Replacement of a liquid of automatic transmission
   Replacement of the fuel filter
   Replacement of a brake liquid
   Road test
   Valve clearing recycling the fulfilled gases (engines K7M and F7R)
   Replacement of a cooling liquid
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Check of level of a liquid of automatic transmission

Transmissionnaja liquid

Level check трансмиссионной liquids very difficult procedure, therefore is better to charge work HUNDRED Renault.

 CHECK

1. Remove a stopper from the top part of a bulk mouth (D) (address to an accompanying illustration). Add 0.5 l of the liquid specified with Specifications in transmission, using a pure bell with the filter, then establish a stopper.

2. Tyre out the car on a viewing hole. If it is necessary, turn away screws of fastening and remove a protective plastic cover of the engine/transmission.
3. Connect test measuring instrument Renault XR25 to diagnostic муфте and enter a code “D04”, then number "04". Establish the lever of a choice of transfers to position “Park”, start the engine and wait, while the temperature of a liquid will not reach 60С.

4. On the working engine turn away a stopper of level of transmission (A) (address to an accompanying illustration). Allow surplus of a liquid to pour out in the container within 20 seconds, then establish a stopper. The quantity of a liquid should be more than 0.1 l; if it not so, liquid level in transmission is wrong.

5. If level is wrong, add 1 l of the liquid specified in Specifications.
Wait, while transmission will cool down, then repeat check procedure again as it is described in the previous paragraphs. After installation of correct level reliably tighten a stopper. Where it is necessary, establish engine protection.
Oil of the main transfer
6. Procedure of check of level is not included into the maintenance service plan but if there were oil leaks, operate as follows.
7. Tyre out the car on a viewing hole.

8. Turn away a stopper of a bulk/control aperture of the main transfer (C), established behind the right power shaft (address to an accompanying illustration).

9. Be convinced that oil level reaches the aperture basis under a stopper. If it not so, fill in oil of the grade specified in Specifications in an aperture under a stopper.
10. Rub off a stopper, then establish and tighten it.