Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   The general description of search of malfunctions in electric equipment system
   The general description of fuses and the relay
   Removal and installation of switches
   Replacement of lamps (external lighting devices)
   Replacement of lamps (lanterns of illumination of salon)
   Removal and installation of blocks of external lanterns
   The general description of adjustment of a direction of an optical axis of light of headlights
   Removal and installation of the instrument panel
   Removal and installation of components of the instrument panel
   Removal and installation of the multipurpose display
   Removal and installation прикуривателя
   Removal and installation of hours
   Removal and installation of sound signals
   Removal and installation of the lever of a screen wiper
   Removal and installation of the motor of a screen wiper and draught
   Removal and installation of the motor of a screen wiper of back glass
   Removal and installation of components of system of a washer of wind glass / a back door
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and radio antenna installation
   The anticreeping alarm system and иммобилизатор the engine
   Removal and installation of components of the electric drive/heating of a forward seat
   System of pillows of safety - the general information and safety measures
   Removal and installation of components of pillows of safety
+ Electric equipment schemes



Removal and installation of blocks of external lanterns

Before removal of any block disconnect a cable of weight from the battery, and connect a wire after block installation.

Headlight

 REMOVAL

1. Remove a bumper as it is described in the Head the Body.

2. Remove the forward index of turn as it will be described more low in this Section.
3. Open a cowl, turn away the fastening screw in the centre of a lattice of a radiator and remove fixing plate.

4. Turn away fastening screws, then by means of a flat screw-driver, release bottom fixing скобы and remove a corresponding half of lattice of a radiator from the car (address to an accompanying illustration).

5. On headlights with a round cover, turn a cover counter-clockwise and remove it from a back part of the block of a lantern. Disconnect sockets of electroconducting and extend a plait of wires from the lantern block (address to an accompanying illustration).

6. On headlights with a rectangular cover, press fixing скобу and disconnect a socket of electroconducting from a back part of the block of a headlight.

7. On the models equipped with system of adjustment of a headlight, disconnect a socket of electroconducting from the motor (address to an accompanying illustration).

8a. Turn away bolts, fastening arms of the bottom fastening of the block of a headlight to a body.

8b. Cнимите the top screw of fastening and скобу.

8c. Extend the lantern block forward.

8d. Cнимите it from the car (address to illustrations).

9a. On the models equipped with system of adjustment of a headlight if it is necessary, turn the motor counter-clockwise (address to illustrations).

9b. Cнимите the motor from a back part of the block.

10. Installation is spent upside-down. In summary adjust a direction of an optical axis of light of headlights.

Antifog headlight

MODELS THE HATCHBACK, THE SEDAN AND SCANIC

 REMOVAL AND INSTALLATION

1. Disconnect an internal cover with a side of an antifog headlight to get access to fixing screws.
2. Turn away fixing screws of an antifog headlight and take the block from a bumper. Disconnect electroconducting sockets.
3. Make installation upside-down.

COMPARTMENT MODELS

 REMOVAL AND INSTALLATION

1. To facilitate access, cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props.

2a. Disconnect an electroconducting socket.

2b. Turn away fixing nuts and remove the block of a lantern from a bumper (address to illustrations).

3. Make installation upside-down. If it is necessary, adjust a direction of an optical axis of light of an antifog headlight, turning a regulator on a back part of the block of a lantern (address to an accompanying illustration).

The forward index of turn

 REMOVAL AND INSTALLATION

1a. Loosen the the screw of fastening of the index of turn on some turns.

1b. Extend the lantern block forward and disconnect an electroconducting socket (address to illustrations).

2. Make installation upside-down.

The forward lateral index of turn

 REMOVAL AND INSTALLATION

1. Accurately disconnect the block of a lantern and remove it from a wing. Release the holder of a lamp, having turned it counter-clockwise, then remove a lantern from the car.
2. Make installation upside-down.

The block of a back lantern

 REMOVAL AND INSTALLATION

1. On models the Hatchback and the Compartment, working in a luggage compartment, turn away the top fixing nut and uncover from a back part of the block of a lantern. On models Scenic the cover is in the panel of furnish of the loose leaf of an arch of a wheel. To improve access, on models the Sedan turn away fastening screws, and disconnect facing (address to an accompanying illustration).

2a. Disconnect an electroconducting socket.

2b. Then turn away fixing nuts and remove the block of a lantern from a back part of the car (address to illustrations).

3. Make installation upside-down.

The back lantern established in a cover of a luggage carrier

MODELS OF THE COMPARTMENT AND THE SEDAN

 REMOVAL AND INSTALLATION

1. Open a luggage carrier cover, then disconnect a cover for access to a back part of a lantern.
2. Disconnect an electroconducting socket, then turn away fixing nuts and remove the lantern block.
3. Make installation upside-down.

MODELS SCENIC

 REMOVAL AND INSTALLATION

1. Open a back door and turn away four bolts of fastening of the panel of furnish of a back door. Let out fixing скобы and accurately remove the panel of furnish of a back door.
2. Remove two holders of a lamp of a back foggy lantern.
3. Turn away seven nuts, крепящих the lantern case to a back door.
4. Accurately release fixing скобы cases, then take it from a back door and disconnect electroconducting sockets.
5. Make installation upside-down.

Additional stoplight

MODELS THE HATCHBACK

 REMOVAL AND INSTALLATION

1. Press fixing скобы and uncover from a back part of the block of a lantern.

2a. Disconnect an electroconducting socket.

2b. Let out fixing скобы and shift a lantern from an arm (address to illustrations).

3. Make installation upside-down.

COMPARTMENT MODELS

 REMOVAL AND INSTALLATION

1. Open a cover of a luggage carrier and disconnect a socket of electroconducting from a back part of the block of a lantern.
2. Accurately let out fixing скобы and remove the block of a lantern from a luggage carrier cover.
3. Make installation upside-down.

MODELS THE SEDAN

 REMOVAL AND INSTALLATION

1. Press fixing скобы and uncover a back part of the block of a lantern.

2a. By means of a screw-driver accurately lift bottom fixing скобы.

2b. Cдвиньте the lantern block forward also disconnect an electroconducting socket (address to illustrations).

3. Make installation upside-down.

MODELS SCENIC

 REMOVAL AND INSTALLATION

1. On models Scenic, open a back door and remove two stoppers in apertures behind the lantern block. Insert a screw-driver into each aperture, release the block of a lantern from скоб. Take the block of a lantern from an outer side of a back door.
2. Let out fixing скобы and remove the holder of a lamp from a back part of the block of a lantern.
3. Installation is spent upside-down.

Licence plate illumination

 REMOVAL AND INSTALLATION

1. Accurately remove by means of a screw-driver the block of a lantern from the back door opening upwards, and disconnect an electroconducting socket.
2. At installation, connect a socket of electroconducting and press the lantern block into place.