Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   The general description of search of malfunctions in electric equipment system
   The general description of fuses and the relay
   Removal and installation of switches
   Replacement of lamps (external lighting devices)
   Replacement of lamps (lanterns of illumination of salon)
   Removal and installation of blocks of external lanterns
   The general description of adjustment of a direction of an optical axis of light of headlights
   Removal and installation of the instrument panel
   Removal and installation of components of the instrument panel
   Removal and installation of the multipurpose display
   Removal and installation прикуривателя
   Removal and installation of hours
   Removal and installation of sound signals
   Removal and installation of the lever of a screen wiper
   Removal and installation of the motor of a screen wiper and draught
   Removal and installation of the motor of a screen wiper of back glass
   Removal and installation of components of system of a washer of wind glass / a back door
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and radio antenna installation
   The anticreeping alarm system and иммобилизатор the engine
   Removal and installation of components of the electric drive/heating of a forward seat
   System of pillows of safety - the general information and safety measures
   Removal and installation of components of pillows of safety
+ Electric equipment schemes



The general description of fuses and the relay

Fuses

The majority of fuses is established in the block of safety locks located in salon of the car from outside of the driver. Additional fuses and some relays are established in the block of safety locks/relays on the left side of an impellent compartment.

On all models except Scenic, safety locks of a high current are in the block of safety locks of the food established in the right part of an impellent compartment, near to the accumulator, on models Scenic the main safety lock on 60А is established under a passenger seat, near to the accumulator (address to illustrations).

To get access to the main block of safety locks, open a cover. For access to the fuses established in an impellent compartment simply disconnect a cover. For access to safety locks of a high current uncover the accumulator or remove the panel of a windscreen and screen wiper levers.

The fuse established under a seat — Scenic

And — a power unit Socket
F — the Fuse 60А

Arrangement of the block of safety locks of a food — Scenic

And — Orange, 60А — the power unit socket, the combined switches of illumination and a screen wiper on a steering column
In — Orange, 60А — the ignition Lock, the combined switches of illumination and a screen wiper on a steering column
With — Black, 40А — air conditioner
D — Red, 60А — heating of a windshield

The additional block of safety locks of a food:
30А — system of injection of fuel (gasoline)
70А — system of preheat (diesel engine)
40А — ABS

Arrangement of the block of safety locks of a food — except Scenic

Brown, 30А — system of injection of fuel (gasoline)
Brown, 70А — system of preheat (diesel engine)
Black, 40А — air conditioner
Green, 60А — a power unit socket

Orange, 60А — the power unit socket, the combined switches of illumination and a screen wiper on a steering column
Orange, 60А — the ignition Lock, the combined switches of illumination and a screen wiper on a steering column and the screen wiper motor

The list of chains which protect the fuse, is on a cover of the block of safety locks.
Before fuse removal, at first switch off a corresponding chain (or ignition), then extend the fuse from clips. The tool for safety lock removal is attached to a back part of a cover. In a safety lock should be we see a wire; if the fuse has burnt down, the wire will be broken or melted off.
At replacement use a safety lock with the identical characteristic. Never replace the fuse more than once without revealing and elimination of a cause of defect. The characteristic of fuses is printed on back parts and in addition they are coded by colour.
Where the fuse protects more than one chain, check up each chain. Always have on the car spare fuses of each characteristic.

The relay

The majority of the relay is established in the block of safety locks located in salon of the car from outside of the driver. Additional relays are established in the block of safety locks/relays on the left side of an impellent compartment.

To get access to the relay block, remove the switch panel from outside the driver as Removal and installation of switches is described in Section.

Turn away the fastening screw, then disconnect a plastic protective plate from the basis on the block of safety locks.

Let out fixing скобы and disconnect four sockets of electroconducting from the basis of the block of safety locks. Release the block of safety locks from lateral fixing скоб, then accurately lower assemblage downwards.

Let out fixing скобы and uncover to get access to various relays (address to illustrations).

Make installation upside-down.
If the chain operated the relay or system does not work, and malfunction of the relay is supposed, include system. If the relay functions, at its inclusion click should be audible. In this case components or system electroconducting are faulty. If it is not audible that the relay joins, to the relay feeding pressure does not arrive, pressure of switching or the relay is faulty. Relay check is reduced to replacement on obviously serviceable, but be cautious — some relays can be similar outwardly and functionally, and others look equally, but execute various functions.
Before relay replacement switch off ignition. Then the relay simply extend from clips and insert the new.