Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assemblage of a forward rotary fist
   Check and replacement of bearings of a nave of a forward wheel
   Removal and installation of a forward rack
   Partition of a forward rack
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, partition and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the spherical hinge of the bottom lever of a forward suspension bracket
   Check and replacement of bearings of a nave of a back wheel
   Removal, check and installation of the back shock-absorber
   Removal and installation of the back stabilizer of cross-section stability (back axis of the closed type)
   Removal and installation of a back axis
   The general description of a partition of a back axis
   Check and adjustment of a road gleam of the car
   Removal and steering wheel installation
   Removal, survey and installation of a steering column
   Removal, survey and installation of the steering mechanism
   Removal and installation of the pump of the steering hydraulic booster
   Prorolling of hydrosystem of the steering hydraulic booster
   Replacement of a protective cover of the steering mechanism
   Removal and installation of a tip of steering draught
   Removal and installation of cross-section steering draught
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of cross-section steering draught

Not to damage steering рейку at draught removal, are necessary a special wrench (№ Dir. 1305 under catalogue Renault) and an assembly clip рейки (№ Dir. 1306 for steering рейки SMI or 1306-01 for рейки TRW) (address to illustrations more low).

On described models there is a steering mechanism of two типов:SMI and TRW. The type рейки can be defined on a brand on картере the steering mechanism. If work is carried out on steering рейке SMI, at installation new assemblage контрящей washers of steering draught is required.

 REMOVAL

1a. Steering рейка it is blocked by an assembly clip.

1b. Remove шаровый the hinge of a tip of draught as Removal and installation of a tip of steering draught is described in Section.

2. Cut collars and remove a protective cover of the steering mechanism from steering draught. It is recommended to replace a protective cover, irrespective of its condition.
3. If special tools are not accessible, turn away the internal hinge of draught from the end the helmsman рейки suitable flat-nose pliers. Block steering рейку, keeping контрящую a washer of the spherical hinge the second flat-nose pliers.

Work cautiously, do not scratch рейку or шаровый the hinge.

4. Separate assemblage of steering draught from рейки. On steering mechanisms SMI will throw out assemblage контрящей washers - it is subject to replacement.
5. If the internal hinge moves too freely or hardly or if steering draught is deformed/is damaged, replace assemblage. Also it is recommended to replace a protective cover of the steering mechanism.


 INSTALLATION

1. Before installation of steering draught remove from it and рейки all traces taking компаунда.

2. On the models equipped with steering mechanism SMI (4), collect new контрящую a washer (3) and a blocking ring (2) and establish them on the end of steering draught (1) (address to an accompanying illustration).

3. Cover a carving of steering draught taking компаундом (Renault recommends Lostite Frenbloc), then establish draught on the end the helmsman рейки. Using a method applied at removal, tighten internal шаровый the hinge of steering draught the effort resulted in Specifications. On steering mechanism SMI be convinced that at a tightening of cross-section steering draught uvulas контрящей washers have got on facets the helmsman рейки (B).
4. Establish a new protective cover on a tip of steering draught and on картере the steering mechanism. Turn a steering wheel from one extreme position in another to be convinced that the protective cover is placed correctly, then attach its new collars.
5. Establish шаровый the hinge of a tip of steering draught as Removal and installation of a tip of steering draught is described in Section.