Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assemblage of a forward rotary fist
   Check and replacement of bearings of a nave of a forward wheel
   Removal and installation of a forward rack
   Partition of a forward rack
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, partition and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the spherical hinge of the bottom lever of a forward suspension bracket
   Check and replacement of bearings of a nave of a back wheel
   Removal, check and installation of the back shock-absorber
   Removal and installation of the back stabilizer of cross-section stability (back axis of the closed type)
   Removal and installation of a back axis
   The general description of a partition of a back axis
   Check and adjustment of a road gleam of the car
   Removal and steering wheel installation
   Removal, survey and installation of a steering column
   Removal, survey and installation of the steering mechanism
   Removal and installation of the pump of the steering hydraulic booster
   Prorolling of hydrosystem of the steering hydraulic booster
   Replacement of a protective cover of the steering mechanism
   Removal and installation of a tip of steering draught
   Removal and installation of cross-section steering draught
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of assemblage of a forward rotary fist

It is necessary to replace a type nut “Nylstop” with a nut “Enko” (it is established without application taking компаунда). If the car is already equipped by a type nut “Enko”, there is no necessity to replace it is it can be used four times. On models with РКПП at installation new cylindrical pins, fastening a power shaft to differential be required.

Grooves of an external SHRUS are covered taking компаундом. Therefore for removal of assemblage of a nave from the power shaft end the stripper is required.

 REMOVAL

1. Uncover a wheel nave/cap (depending on model), then ослабьте a nut of a power shaft and wheel bolts.
2. Block back wheels of the car, cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props. Remove a forward wheel.
3. On the models equipped ABS, turn away bolts of the gauge of speed of rotation of a wheel, take away it from assemblage of a nave and tie up to a body (address to the Head Brake system). Pay attention that there is no necessity to disconnect conducting.
4. Turn away a fixing nut of a power shaft. If the nut has not been weakened while the car was not поддомкрачен, establish in a nave two bolts of a wheel and reliably tighten them. Ask the assistant to press firmly a brake pedal to block a nave, then by means of a nest and a lengthening core ослабьте and remove a nut. Alternatively, make the doubled tool from two pieces of a steel strip (one long, one short), having connected their bolt to a nut. Attach the tool to a nave, using two bolts of a wheel and, keeping it thus motionless, turn away a fixing nut of a power shaft.
5. Loosen the also remove a nut, крепящую a tip of cross-section steering bent for to a rotary fist, then separate шаровый the hinge from a nave by means of a special stripper.

6. If it is necessary to remove nave bearings, remove a brake disk as it is described in the Head Brake system. Otherwise turn away two bolts, fastening assemblage of an arm of a support to a rotary fist, and remove a support from a disk (address to an accompanying illustration). A wire or twine piece tie up a support to a spring of a forward suspension bracket so not to stretch a brake hose. If it is necessary, turn on from a rack bolts of an arm of conducting / a brake hose.

7. Remove a nut and a coupling bolt, крепящий the bottom lever to a rotary fist. Accurately wring out шаровый the hinge from a rotary fist, trying not to damage шаровый the hinge and protective covers of a power shaft. Pay attention to the plastic protective plate established on a core of the spherical hinge.

8. Remove two nuts/washers from bolts, крепящих a rotary fist to a suspension bracket rack, having remembered that nuts are established from the back party of a rack (address to an accompanying illustration). Take bolts and prop up assemblage of a rotary fist.

9. Let out the SHRUS of a power shaft from a nave and remove assemblage of a rotary fist. Pay attention that on SHRUS grooves it is put taking компаунд. Use a hammer and выколотку from soft metal, or a stripper to supersede the hinge from a nave (address to an accompanying illustration). Support a power shaft not to damage SHRUS and their covers.


 INSTALLATION

1. Clear and dry up SHRUS and nave grooves, then put on the SHRUS shaft taking компаунд (Renault recommends Lostite Scelbloc).

2. Combine SHRUS and nave grooves and displace a nave on a power shaft into position. Insert two bolts of fastening of a rotary fist to a suspension bracket rack (from the forward party of a rack), then establish on them washers and nuts and tighten the effort resulted in Specifications (address to an accompanying illustration).

3. Establish a washer and acquire a new nut of a power shaft of type “Enko” (the Note above see).
4. Be convinced that the plastic protective plate still costs on the spherical hinge of the bottom lever, then establish a hinge core in a rotary fist. Insert a coupling bolt of the hinge and tighten a fixing nut the effort resulted in Specifications.
5. Insert шаровый the hinge of a tip of cross-section steering draught into a rotary fist and tighten a fixing nut the effort resulted in Specifications.
6. Insert шаровый the hinge of a tip of cross-section steering draught into a rotary fist and tighten a fixing nut the effort resulted in Specifications.
7. On the models equipped ABS, establish in a nave the gauge and tighten a fastening bolt the regulated effort of an inhaling (address to the Head Brake system).

8. Establish a brake disk, levelling the labels made before removal, and tighten fastening screws the effort resulted in Specifications. Place assemblage of a support of a brake into position on a disk. Put on a carving of bolts of a support some drops taking компаунда (Renault recommends Lostite Frenbloc), then establish bolts and tighten their regulated effort of an inhaling (the Head Brake system, address to an illustration).

9. Block a nave a method applied during its removal, and tighten a new fixing nut of a power shaft the effort resulted in Specifications. Alternatively, slightly tighten a nut at this stage, having postponed its definitive inhaling till the moment when the car will be lowered on the earth.
10. Be convinced that the nave rotates freely, then establish a wheel and lower the car on the earth. Tighten wheel bolts the effort resulted in Specifications.